 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| NJU7505 BAND PASS FILTER FOR AUDIO SPECTRUM ANALYZER DISPLAY ! GENERAL DESCRIPTION The NJU7505 is a band pass filter for audio spectrum analyzer display. It consists of high and low band pass filters, CR oscillation circuit, control circuit and DC transfer circuit. Each band pass filter using the switched capacitor filter technology operates at the shared time by 5 bands which filter constant is switched by the internal clock. Therefore, the audio signal shared of 5 bands is output from a serial output terminal. The 10 bands version using the double by the cascade connection is prepared. ! PACKAGE OUTLINE NJU7505XD NJU7505XM ! FEATURES " BPF for the audio spectrum analyzer display of the 5 bands " 10 bands extension is available by the cascade connection (Version of A: For 5-band application by the single) (Version of B: For 10-band application by the double) " BPF using the switched capacitor filter technology " CR oscillation circuit on chip (External clock input is available) " Power-on initialization circuit on chip (External reset input is available) " C-MOS Technology " Package Outline DIP8, DMP8 ! PIN CONFIGURATION OSC1 OSC2 RST/CLKO RD 1 2 3 4 5 6 7 8 VDD AIN AOUT VSS ! BLOCK DIAGRAM RST/CLKO RD Audi o Signal Control Signa Crock Signal OSC1 OSC2 OSC fOSC fOSC/16 Cont rol Circuit fOSC/4 iH iL RL RH Power-on Initialize H L BPF High Band High Band Peak Detector Lev el Shif ter & Out Put BUF AOUT AIN Input BUF LPF BPF Low Band Low Band Peak Detector VDD VDD AGND VSS VSS Ver.2004-06-04 -1- NJU7505 ! TERMINAL DESCRIPTION NO. SYMBOL FUNCTION 1 OSC1 External Resistor connecting terminal. 2 OSC2 External Resistor connecting terminal or External clock input terminal. Both as Reset input terminal 3 RST/CLKO and the clock of (2/3)*fosc output terminal. 4 RD Trigger signal for reading-out the AOUT of each band output terminal. 5 VSS GND 0V VDD 8 Positive power supply +5.0 V 6 AOUT Peak voltage of each band output terminal. 7 AIN Audio signal input terminal. ! VERSION LINEUP AND PEAK FREQUENCY The NJU7505 prepares two version of A and B which are different of the peak frequency of each bands. The version of A is recommended for the 5 bands application using the single and the version of B is recommended for the 10 bands using the double by the cascade connection, however, the version of A can be used for the 10 bands using the double and the version of B can be used for the 5 bands using the single. Peak Frequency ( Hz ) Using the single Using the double Version of A Version of B Version of A Version of B 12k 18k 12k 18k 8k 12k 3.5k 5.3k 3.5k 5.3k 2.3k 3.5k 1k 1.5k 1k 1.5k 670 1k 250 375 250 375 165 250 63 95 63 95 * 42 63 Band f1a f1b f2a f2b f3a f3b f4a f4b f5a f5b Note 1) The bands of f1a, f2a, ... f5a correspond to the master side and the bands of f1b, f2b, ... f5b correspond to the slave side at the cascade connection of the double. Note 2) It may not be output along the expectation at the peak frequency of * marking, since the sampling time is not enough. The example of using the single OSC1 AOUT f 1a to f5a OSC1 The example of using the double AOUT f 1a to f5a OSC1 AOUT f 1b to f5b NJU7505 f OSC OSC2 f OSC NJU7505 Master RST/CLKO 2/3 * f OSC NJU7505 Slave OSC2 -2- Ver.2004-06-04 NJU7505 ! FUNCTIONAL DESCRIPTION # Interface to external controller The example of the interface between the NJU7505 and the external controller is shown below; (1) Example of the interface to the external controller ( Using the single ) After the RST signal from the external controller is input and then the internal circuit is initialized, each band data is output as shown below timing chart; Since the RD signal is output before each band is switched, the external controller is to count the number of the RD signal and is to recognize the status of the band and is to read the output data from the AOUT terminal through the external A/D converter. The output type of the external controller connected to the RST/CLKO terminal as the RST input should be the N-channel and open-drain type or the diode should be connected between the RST/CLKO terminal and the output terminal of the external controller, so that the voltage of the RST/CLKO terminal is not gotten over the VSS level. AIN OSC1 NJU7505 A/D CONVERTER AOUT OSC2 fOSC VSS RST/CLKO RD COM 3*214 / fO SC A OUT RD RST f1 f1 f2 f2 f3 f3 f5 f5 f1 f1 f2 f2 f4 f4 f3 f3 f1 f1 f1 f2 f2 f3 248 / fosc Since the RD signal is output before 248/fOSC of each band switched, the output data should be read out within the limited time as shown right; AOUT RD Available Period of Read-out 8 / fosc AOUT fn f1 If the RST signal which pulse width is more than 4/fOSC is input, the internal circuit is initialized and the data of f1 band is output from the AOUT terminal after 52/fOSC of the rise edge of the RST signal. 4/ fosc[MIN] 52/ f osc RST Ver.2004-06-04 -3- NJU7505 (2) Example of the interface to the external controller (Using the double) The 10 bands application is available using the cascade connection of the double NJU7505 as shown blow. After the RST signals from the external controller are input to each of the master and the slave of the NJU7505 and then each internal circuit is initialized, each band data is output as shown below timing chart; Since the RD signals are output from the master and the slave before each band is switched, the external controller is to count the number of the RD signals and is to recognize the status of the band and is to read the output data from each AOUT terminals through the external A/D converter. The master clock for the slave is provided with the output signal from the RST/CLKO terminal of the master. The master clock for the slave is stopped when the RST signal is input from the external controller to the master, so that the RST/CLKO terminal of the master is used both as the RST input of the master and the master clock for the slave. The output type of the external controller connected to each RST/CLKO terminal as the RST input should be the N-channel and open-drain type or the diode's should be connected between each RST/CLKO terminal and the output terminals of the external controller, so that the voltage of each RST/CLKO terminal is not gotten over the VSS level. AIN AIN OSC1 OSC2 A/D CONVERTER AOUT NJU7505 Slave AOUT NJU7505 OSC2 Master VSS RST/CLKO RD RST/CLKO RD COM Master A OUT RD RST f1 f1 f2 f2 3*214 / fO SC f3 f3 f5 f5 f1 f1 f2 f2 f4 f4 f3 f3 f1 f1 f2 f2 f3 f3 f1 f1 f2 Slave A OUT f1 f1 RD RST 3*214 / fO * 3/2 SC f2 f2 f3 f3 f5 f5 f1 f1 f2 f2 f4 f4 f3 f3 f1 f1 f2 -4- Ver.2004-06-04 NJU7505 Since each RD signal of the master and the slave is output before 248/fOSC (248/fOSC*3/2) of each band switched, the output data should be read out within the limited time as shown right; * The "( )" is corresponded to the slave. 248 / fosc (248/ fosc*3/2) AOUT RD Available Period of Read-out 8 / fosc (8/ fosc*3/2) If the RST signal which pulse width is more than 4/fOSC is input to the master, the internal circuit is initialized and the data of f1 band is output from the AOUT terminal of the master after 52/fOSC of the rise edge of the RST signal. The RST signal for the slave should be set to "L" level while the RST signal for the master is "L" level and should keep "L" level more than 6/fOSC. So the slave operates as same as the master after 78/fOSC of the rise edge of the RST signal for the slave. AOUT (Master) fn f1 4/fosc[MIN] RST (Master) 52/ fsoc RST (Slave) 6/fosc[MIN] AOUT (Slave) 78/ fsoc f 1' f n' Ver.2004-06-04 -5- NJU7505 ! ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL RATINGS Supply Voltage VDD -0.3 to +7 VIN -0.3 to VDD+0.3 Input Voltage VIO -0.3 to 0 Output Voltage VOUT -0.3 to VDD+0.3 Power Dissipation PD 500(DIP), 300(DMP) Operating Topr -30 to 85 Temperature Storage Temperature Tstg -55 to 125 UNIT V V V mW C C (Ta=25C) NOTE 7 5, 8 Note 3) If the IC are used on condition above the absolute maximum ratings, the IC may be destroyed. Using the IC within electric characteristic conditions will cause malfunction and poor reliability. Note 4) All voltage values are specified as VSS = 0V. Note 5) When the voltage of the RST/CLKO terminal is gotten over the VSS level, the diode should be connected between the RST/CLKO terminal and the external. Note 6) Decoupling capacitor should be connected between the VDD terminal and the VSS due to the stabilization of the operation. Note 7) Applied to the AIN or the OSC2 terminals. Note 8) Applied to the RST/CLKO terminal. ! ELECTRICAL CHARACTERISTICS DC CHARACTERISTICS PARAMETER Operating Voltage Operating Current SYMBOL VDD IDD IIL1 IIH1 IIL2 VILC VIHC VOL1 VOH1 VOL2 VOH2 VOS CONDITITONS (VDD=5V, VSS= 0V, Ta=25C) MIN TYP MAX UNIT NOTE 4.5 5.0 6.0 V VDD TERMINAL 6.0 12 mA VIL1=0V -0.1 -0.05 -0.033 mA Input Leak Current 1 AIN TERMINAL 0.1 VIH1=5V 0.033 0.05 Input Leak Current 2 RST/CLKO TERMINAL VIH2=0V -0.2 -0.1 -0.05 mA External Clock 0 1.5 OSC2 TERMINAL V Input Voltage 3.5 5.0 IOL1=100A 0 0.5 V Output Voltage 1 RD TERMINAL 4.5 5.0 IOH1=-100A RST/CLKO IOL1=100A 0 0.5 Output Voltage 2 V TERMINAL 4.25 4.5 4.75 IOH1=-5A Output Offset Voltage AOUT TERMINAL AIN:OPEN 300 mV 26.0 dB 9,10,11 AOUT TERMINAL Sine Wave Input BPF Output Voltage VOUT VIN=200mVp-p fIN=f1 to f5 3.5 V 9,10 Note 9) This specification is tested on condition of fCLK=400KHz (The external clock is input to the OSC2 terminal through the capacitor for AC coupling. Note 10) Each input frequency of f1 to f5 is referred to the table of the " VERSION LINEUP AND PEAK FREQUENCY ". Note 11) This specification is calculated from " VOUT / VIN ". -6- Ver.2004-06-04 NJU7505 ! AC CHARACTERISTICS PARAMETER Oscillation Clock Freq SYMBOL CONDITIONS fOSC RST/CLKO Terminal VDD=5V RST/CLKO Terminal VILC=0V External Clock Frequency fCLK VIHC=VDD Master RD Pulse Width tPWRD RD Terminal Slave Master RST Pulse Width tPWRS RST/CLKO Terminal Slave RST Rise/Fall Time tr, tf RST/CLKO Terminal Note 12) The example for the CR Oscillation OSC1 RT OSC2 CT ( VDD=4.5 to 6.0V, VSS=0V, Ta=25C) MIN 360 TYP 400 400 8/fOSC 8/fCLK 12/fOS C MAX 440 800 UNIT NOTE KHz 12 KHz 13 s 14 12/fCLK 4/fOSC 4/fCLK 6/fOSC 6/fCLK 100 s nA 15 15 RT: 13K(2%) CT: 220pF(5%) *The oscillation clock frequency is calculated from the output frequency of the RST/CLKO terminal by 3/2. VSS Note 13) The example for the external clock input Open OSC1 The input signal for the OSC2 terminal should be the condition of the pulse of DUTY50%10%. * The oscillation clock frequency is calculated from the output frequency of the RST/CLKO terminal by 3/2. Oscillator OSC2 Note 14) The output wave form of the RD terminal. 0.8VDD 0.8VDD tPWRD Note 15) The input wave form of the RST terminal. tf 0.8VDD 0.2VDD TPWRS tr 0.8V DD 0.2VDD Ver.2004-06-04 -7- NJU7505 ! APPLICATION CIRCUIT (1) AUDIO IN AUDIO IN Lch Rch AUDIO OUT AUDIO OUT RESONANCE CIRCUIT NJU7305 RESONANCE CIRCUIT *1 *2 ATT. AIN OSC1 13K OSC2 NJU7505 VSS RST/CLKO RD 220pF AOUT *3 A/D COM DISPLAY DRIVER DISPLAY *1 ) The capacitor for AC coupling connected to the AIN terminal should be needed. *2 ) Connecting the attenuator, the dynamic range of the display can be changed. *3 ) When the voltage of the output terminal of the COM gets over the VSS level, the diode should be connected between the RST/CLKO terminal and the output of the COM. -8- Ver.2004-06-04 NJU7505 ! APPLICATION CIRCUIT (2) AUDIO IN AUDIO IN Lch Rch AUDIO OUT AUDIO OUT RESONANCE CIRCUIT NJU7305 RESONANCE CIRCUIT ATT. AIN *2 *1 ATT. *2 AIN OSC1 13K NJU7505 OSC2 NJU7505 OSC2 220pF VSS RD RST/CLKO RST/CLKO RD AOUT *3 *3 AOUT A/D A/D COM DISPLAY DRIVER DISPLAY *1 ) The capacitor for AC coupling connected to the AIN terminal should be needed. *2 ) Connecting the attenuator, the dynamic range of the display can be changed. *3 ) When the voltage of the output terminal of the COM gets over the VSS level, the diode should be connected between the RST/CLKO terminal and the output of the COM. [CAUTION] The specifications on this databook are only given for information , without any guarantee as regards either mistakes or omissions. The application circuits in this databook are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights. Ver.2004-06-04 -9- |
Price & Availability of NJU7505
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |